The continuous TripleHard® line in Kuopio, designed and built by ILMAR, seen from the front along its full length, the hall darkened around it

The continuous line

Trivalent hard chrome in one
continuous pass.

The continuous TripleHard® line in Kuopio is the industrial-scale reference line for hydraulic cylinder rods: surface preparation, etching, nickel and Cr(III) layers in one enclosed pass. It is running, it is open for visits, and every customer line is engineered from its data.

The reference line, running in Kuopio.

  • Running
  • Open for visits
  • Version 1 complete

The continuous TripleHard® line in Kuopio is running, open for visits, and produces the data for the lines built for customers. Version 1 is complete: the first-round run parameters are locked, and optimisation continues. TripleHard® is already in industrial production on a converted open-tank line, in smaller volumes; proving high-capacity continuous production is the job of this line.

Four stages

From bare steel to
TripleHard®, without stopping.

  1. 1Surface preparation

    Cleaned and activated, ready for the layers.

  2. 2Etching

    A controlled etch opens the steel surface for the anchor layer.

  3. 3Nickel deposition

    The nickel anchor layer goes on first. It bonds to the activated steel, gives TripleHard® its adhesion and carries much of its corrosion protection.

  4. 4TripleHard® Cr(III) layers

    Trivalent chromium is built up over the nickel to hard-chrome-level hardness, without heat treatment.

Schematic, not to scale. A rinse follows every stage.

How it differs

Traditional plating stops between every step. This line does not.

Conventional Cr(VI) hard chrome plating is a batch process: open tanks, an overhead crane, and an operator between every bath. The continuous line replaces the sequence with a single automated pass.

4 baths1 pass
Surface preparation, etching, nickel and Cr(III) in one uninterrupted run
OperatorNo hand transfer
No part is lifted between baths by hand, and the baths are enclosed
Traditional platingThe continuous line
Separate work stagesOne uninterrupted process
Open tanksFully enclosed system
Crane transfer between bathsAutomated conveying
Fume extraction over open tanksVapours contained in the line
An operator in ear defenders and gloves feeds a hydraulic cylinder rod onto the entry rail of the enclosed TripleHard® line in Kuopio, designed and built by ILMAR

Line designed and built by ILMAR

Safe by design

Chemicals stay inside the line.

The enclosed design keeps chemicals, mist and emissions contained. Handling is automated, so operators are kept away from the chemicals.

  • Operator safe.

    Minimal contact with chemicals and moving parts

  • Fully enclosed.

    Splash, mist and emissions contained

  • Less chemical use.

    Less waste, lower disposal fees

  • Monitored online.

    Real-time tracking, deviation alarms and a record for every part, in partial use on this line.

Control and data

Online monitoring in every line licence.

Trivalent chromium is sensitive to its process conditions, so the line is built around control. Savroc's online monitoring software is built to track the process in real time, flag deviations and keep a record of every part. It is included in every line licence, in partial use on the reference line in Kuopio and continuously developed.

  • Real-time process tracking.
  • Deviation alarms.
  • A record for every part.

The same quality on every licensed line.

In development Sensors are being added to the baths and tanks; monitoring is planned and under development.

From pilot to industrial scale

Built from a 3D-printed pilot in under a year.

The self-built 3D-printed pilot line seen from the side: a row of black printed cells on a rail, on a concrete floor
The 3D-printed pilot line, 2025, seen from the side. More than 50 versions ran on it.
  1. The continuous process is developed on a self-built, 3D-printed pilot line. More than 50 versions were tested over months of near-daily experiments.

  2. The industrial-scale line arrives in Kuopio.

  3. Installation complete; the line ran for the first time the same day. Read the news

  4. First coatings produced. Results reported excellent.

  5. Version 1 complete: the first-round run parameters are locked and optimisation continues.

  6. Plan: mass production on the first continuous customer line, built by a qualified equipment partner, with the process commissioned by Savroc.

Who does what

Savroc designs the process. Qualified equipment partners build the lines.

  • Technology owner and licensor

    Savroc

    Leads the project with you: simulation, the process and line design, commissioning in your plant and process support in production. Licenses TripleHard®.

  • Built the Kuopio line

    ILMAR

    The industrial-scale line in Kuopio was built by ILMAR (Italy): equipment engineering, automation and manufacturing, to Savroc's process design.

  • Built for your plant

    Your line

    A customer line is built by a qualified equipment partner to Savroc's process design, or converted from an existing line; Savroc commissions the process in your plant.

The continuous TripleHard® line in Kuopio, designed and built by ILMAR, seen from the side in the darkened hall, with a bundle of rods waiting in the foreground

See it for yourself

The line runs in Kuopio. Come and watch it coat a rod.

Bring your drawings and the targets your parts must meet. Savroc's engineers show you the line, the test data and what a project in your plant would look like. No commitment. The line is open for visits.

Book a visit

Savroc sales@savroc.com